1. Home
  2. Capabilities

How we make brass parts

Rod comes from approved mills. Forging, turning, stamping, secondary operations, plating and packing happen in our plant in Jamnagar; material tests (composition, strength) go to an outside lab.

Processes

Each part is routed to the process that gives the lowest cost at its volume.

Design for cost: with each quote we suggest where cost can come out, such as forging instead of machining from bar, a special bar profile to cut operations, or relaxing non-critical dimensions. You approve every change.

CNC turning

Complex profiles and multiple features in one set-up. Used for samples, short and medium runs, and parts that change often.

Ø5–100 mm · ±0.05 mm

Cam-automat turning

Bar-fed cam-operated automats for long runs of small and medium parts at the lowest piece price.

bar-fed

Hot forging

Near-net brass forgings for bodies, tees and manifolds, then machined to finish. Less material and fewer operations than machining from bar.

25 g – 1.0 kgshot-blasted · natural · bright

Special-purpose machines

Single-operation machines, built in-house with our own fixtures, for turning, drilling, threading and milling on large batches of repeat parts. They take manual handling, and with it errors, out of repeat jobs.

drill · tap · mill · slot

Stamping

Earth tags, washers, fuse and switch parts and other electrical parts pressed from brass, copper and steel strip.

±0.05 mm on punched features

Secondary operations

Knurling, broaching, marking and sub-assembly, such as fitting seals into glands before packing.

knurl · broach · mark

Machine park

66 machines: 12 CNC lathes, 20 cam automats, 21 special-purpose machines built in-house, 10 drilling machines and 3 presses.

Machine typeQtyBar or part rangeNotes
CNC lathes12Ø5–100 mm barSamples to medium runs; cross-holes and flats in a second operation
Cam-operated automats20Small and medium partsBar-fed, long runs
Special-purpose machines21—Built in-house: turning, drilling, threading, milling
Drilling machines10—Drilling and tapping
Presses3——

Range & accuracy

ProcessParameterValue
TurningBar diameterØ5–100 mm
TurningPart length≤ 100 mm
TurningDiameter tolerance±0.05 mm
TurningRun-out0.05 mm
ForgingPart weight25 g – 1.0 kg
StampingPunched features±0.05 mm
AllGeneral toleranceISO 2768-m unless the drawing states otherwise

Fits tighter than ±0.05 mm: send the drawing; the quote says whether we can hold them.

Materials: CW614N and CW617N as standard; on request low-lead DZR CW511L, lead-free CW724R and DZR CW602N. Grade details

Threads

SystemStandardTypical useChart
MISO 261 · EN 60423 (glands)Turned parts, metric cable glandsMetric chart
PGDIN 40430Cable glands and accessoriesPG chart
G (BSP)ISO 228-1Fittings, gland accessories, insertsBSP chart
R / Rc (BSPT)ISO 7-1Tapered pipe fittings—
NPTASME B1.20.1Fittings for North AmericaNPT chart
UNC / UNFASME B1.1Inch fasteners and turned parts—
BA / BSWBS 57 / BS 84Older British equipment—

Special and customer-specific threads made to drawing. Parallel threads gauged GO / NO-GO.

Plating & finishing

Nickel
Corrosion resistance and appearance
Tin
Electrical contact parts, solderability
Zinc
Low-cost corrosion protection
Silver
High-conductivity electrical contacts, on request
Chrome
Decorative and wear-resistant surfaces, on request
Natural
Bright-machined, shot-blasted (forgings)

Nickel, tin and zinc plating is done in our plant; silver and chrome on request. Thickness is measured per lot and recorded on the route card. State the thickness you need in µm in the quote request.

Packing & dispatch

Packed to your specification, with traceable labels (label contents: see Quality).

  • Single-piece packing
  • Small parts in pouches
  • Bubble or foam bags
  • Blister packs
  • Export cartons, strapped and labelled

Pieces per bag, carton weight and pallet type to your specification. Shipping terms: Ordering & shipping.

Check a part against these ranges

Send the drawing; if it's outside our range, the reply says so.